Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 47

Page: 47 / 296

Note:

Callouts for slots

apply when the riser is installed in the riser 1 position. Callouts for slots

apply when the riser is installed in the riser 2 position.

Figure 21. Slot 3 to 4 and slot 12 to 13 riser connectors

Table 16. Slot 14 to 15 riser connectors

Callout

3 12

PCIe3 x16 (Slot 3 or 12)

4 13

PCIe3 x16 (Slot 4 or 13)

Slot 10 to 15 riser connectors

There are five PCIe3 x16, full height, half length connectors and one ML2 PCIe3 x16 connector in the slot 10
to 15 riser.

Figure 22. Slot 10 to 15 riser connectors

Table 17. Slot 10 to 15 riser connectors

Callout

PCIe3 x16 (Slot 10)

PCIe3 x16 (Slot 13)

PCIe3 x16 (Slot 11)

PCIe3 x16 (Slot 14)

PCIe3 x16 (Slot 12)

ML2 PCIe3 x16 (Slot 15)

Slot 16 to 17 riser

There are two PCIe3 x8, full height, half length connectors in the slot 16 to 17 riser.

Chapter 2

Server components

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands