Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 279

Page: 279 / 296

• Thirty-one spherical stakes

Figure 153. Removing stakes on the front cover

Step 2. Separate the sheet metal shield from the front cover.

Figure 154. Separating sheet metal shield on the front cover

Step 3. Use a screwdriver and remove the four screws; then, remove the four latch springs.

Appendix A. Hardware disassembling for recycle

269

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands