Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 236

Page: 236 / 296

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

Figure 134. Storage board assembly installation

Step 1. Align the upper and lower storage board assembly boards with the rails in the storage tray; then,

insert the storage board assembly.

Step 2. Slide the storage board assembly into the storage tray until the release clips on the lower board

snap into the locked position.

Step 3. Connect all cables on the storage board assembly that go to connectors in the storage tray. See

“Internal cable routing” on page 40.

After you install the storage board assembly, install the storage tray and front cover. See “Install the storage
tray (fully removed)” on page 234 and “Install the front cover” on page 132.

Storage interposer replacement

Storage interposers are in the upper and lower trays that are accessed from the front of the server.

Procedures for removing and installing storage interposers in the upper and lower trays are different.

Remove a storage interposer (upper tray)

The upper storage interposer is in the upper compute tray or optional storage tray that is accessed from the

front of the server. After removing the upper tray and fan cage, disconnect the RAID card from the storage

interposer and lift it out of the way; then, remove the screw securing the storage interposer and remove the

storage interposer from the tray.

S002

CAUTION:

226

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands