Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 243 | Manualshive

Page: 243 / 296

background image

Figure 139. Storage tray removal to stop position

Step 1. Press the button on each release lever; then, simultaneously rotate the release levers until they are

perpendicular to the chassis.

Step 2. Pull storage tray forward evenly until it stops; then, close the release levers.
Step 3. Press the release tabs on either side of the tray; then, slide the tray fully forward evenly and remove

it from the chassis.

Attention:

• Be prepared to support the full weight of the storage tray when you remove it from the chassis.
• Do not use the release levers as handles to support the storage tray.

Figure 140. Storage tray removal from chassis

.

Hardware replacement procedures

233

«
...
241
242
243
244
245
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

SBXL52 - Server Compute Blade

Brand: Intel Pages: 126

SUPERSERVER 8045C-3R

Brand: Supermicro Pages: 118

SuperServer 1026T-M3

Brand: Supero Pages: 104

Brand: IBM Pages: 98

xPort Pro XPP1004000-02R

Brand: Lantronix Pages: 17

Brand: Supermicro Pages: 62

Brand: 7thSense Pages: 28

Brand: Eneo Pages: 94

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

SuperServer 5013G-M

Brand: Supero Pages: 104

Brand: RIOT Pages: 18

PRIMEQUEST 3800E

Brand: Fujitsu Pages: 38

Brand: Fujitsu Pages: 36

Primergy BX2560 M1

Brand: Fujitsu Pages: 68

PRIMEQUEST 3000 Series

Brand: Fujitsu Pages: 44

Brand: Fujitsu Pages: 56

PRIMEQUEST 2800B3

Brand: Fujitsu Pages: 28

Brand: Fujitsu Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands