Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 99 | Manualshive

Page: 99 / 296

background image

Chapter 9. Hardware replacement procedures

This section provides installation and removal procedures for all serviceable system components. Each

component replacement procedure references any tasks that need to be performed to gain access to the

component being replaced.

The ThinkAgile VX MT 7Z12/7Z13 Series appliances and nodes are based on the ThinkSystem SR950 server.

For hardware replacement procedures not listed in this section:

http://thinksystem.lenovofiles.com/help/topic/7X05/maintenance_manual_hardware_replacement_
procedures.html

For more information about ordering parts:

https://datacentersupport.lenovo.com/us/en/products/solutions-and-software/thinkagile-vx/vx7820/7z13/parts/
display/compatible

https://datacentersupport.lenovo.com/us/en/products/solutions-and-software/thinkagile-vx/vx-4u-node/7z12/
parts/display/compatible

Note:

If you replace a part, such as an adapter, that contains firmware, you will also need to update the

firmware for that part. For more information about updating firmware, see “Update the firmware” on page 68.

Installation Guidelines

Before installing components in your server, read the installation guidelines.

Before installing optional devices, read the following notices carefully:

Attention:

Prevent exposure to static electricity, which might lead to system halt and loss of data, by

keeping static-sensitive components in their static-protective packages until installation and handling these
devices with an electrostatic-discharge wrist strap or other grounding system.

• Read the safety information and guidelines to ensure that you work safely.

– A complete list of safety information for all products is available at:

http://thinksystem.lenovofiles.com/help/topic/safety_documentation/pdf_files.html

– “Handling static-sensitive devices” on page 91.

• Make sure the components you are installing are supported by the server. For a list of supported optional

components for the server, see

http://www.lenovo.com/us/en/serverproven/

• When you install a new server, download and apply the latest firmware. This will help ensure that any

known issues are addressed, and that your server is ready to work with optimal performance. Go to

ThinkAgile VX Best Recipe

to download firmware updates for your server.

Important:

Some cluster solutions require specific code levels or coordinated code updates. If the

component is part of a cluster solution, verify that the latest level of code is supported for the cluster
solution before you update the code.

• It is good practice to make sure that the server is working correctly before you install an optional

component.

© Copyright Lenovo 2020

89

«
...
97
98
99
100
101
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: IBM Pages: 220

SuperServer E301-9D-8CN8TP

Brand: Supermicro Pages: 117

Brand: Olive Pages: 24

FusionServer 2298 V5

Brand: Fusion Pages: 89

Brand: ABB Pages: 9

Brand: ABB Pages: 68

VGF-HS1 - Vaio Home Server

Brand: Sony Pages: 2

Brand: Sony Pages: 28

Brand: Sony Pages: 313

Brand: StarTech.com Pages: 67

Brand: Stute Engineering Pages: 29

Brand: Generac Power Systems Pages: 52

Brand: Gigabyte Pages: 86

Brand: Gigabyte Pages: 110

Brand: Gigabyte Pages: 173

Brand: Gigabyte Pages: 166

Brand: Gigabyte Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands