Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 22 | Manualshive

Page: 22 / 296

background image

Configuration 2. Four-Socket Upgradable

The ThinkAgile VX7820 Appliance/VX 4U Certified Node is available in several configurations.

•  2 or 4 processors, must be 8100 Series processors
•  4 processors in a ring topology
•  12 drive bays including up to 6 NVMe (2 NVMe with 2 processors)
•  Up to 15 rear PCIe slots with 4 processors (6 rear slots with 2 processors)
•  Filler installed in the upper tray area
•  Once upgraded, the system will have 24 drive bays

Processor configurations

This configuration supports 2, 3, or 4 processors.

• 2-processor configuration. Processors are installed in location 1 and 2.
• 4-processor configuration. Processors are installed in locations 1, 2, 3, and 4.

Figure 5. Processor numbering (viewed from the front of the server)

PCIe slot connectivity

The following table shows the processor to PCIe slot connectivity:

12

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
20
21
22
23
24
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Enterprise Server S80

Brand: IBM Pages: 282

Flex System x440 Compute Node

Brand: IBM Pages: 584

Brand: Avaya Pages: 19

eServer 130 xSeries

Brand: IBM Pages: 156

ProLiant DL580 Gen10

Brand: HPE Pages: 158

SUPERSERVER 6015C-M3

Brand: Supero Pages: 118

Brand: Artesyn Pages: 190

Brand: IBM Pages: 82

Brand: Kyocera Pages: 207

ConnectPort LTS 16

Brand: Digi Pages: 169

FP-SER-ETH-SERVR2

Brand: RCI Pages: 17

Brand: SystemBase Pages: 118

Brand: Axis Pages: 10

DeviceMaster LT

Brand: Comtrol Pages: 136

Brand: IBM Pages: 68

206m - eServer xSeries - 8485

Brand: IBM Pages: 92

Brand: Gigabyte Pages: 21

Brand: NuPrime Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands