Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 108

Page: 108 / 296

remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

“

” on page 89 “

” on page 65

Before you remove an adapter from slot 16 to 17:

1. Disconnect and label all cables connected to adapters in the I/O tray; then, remove the I/O tray. See

“Remove the I/O tray” on page 152.

2. Remove the riser for slot 16 to 17. See “Remove the riser for slot 16 to 17 (riser 3)” on page 217.

Complete the following steps to remove an adapter from slot 16 to 17.

Watch the procedure

. A video of the installation process is available:

•

YouTube

•

Youku

Figure 47. Adapter removal (slot 16 to 17)

Step 1. Open the retention latch.
Step 2. Disengage the adapter from its connector on the riser and lift the adapter from the riser.

After you remove the adapter:

• If you are removing the adapter and are not installing a replacement:

1.  Install a filler in the empty adapter slot and close the retention latch.
2.  Install the riser. See “Install the riser for slot 16 to 17 (riser 3)” on page 222.
3.  Install the I/O tray and connect all cables. See “Install the I/O tray” on page 154.

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands