Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 64

Page: 64 / 296

Note:

In this illustration, the image on the left shows the tray right-side up and the image on the right shows

the tray upside down.

Figure 40. Cable routing, NVMe drive cables (upper tray with system board)

Note:

In this illustration, the image on the left shows the tray right-side up and the image on the right shows

the tray upside down.

Figure 41. Cable routing, NVMe drive cables (upper tray with storage-board assembly)

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands