Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 112 | Manualshive

Page: 112 / 296

background image

Important:

You must remove the riser from the I/O tray before installing an adapter.

Complete the following steps to install a LOM adapter in slot 9.

Watch the procedure

. A video of the installation process is available:

•

•

Figure 50. LOM adapter installation (slot 9)

Step 1. Attach the extension bracket to the top of the LOM adapter using two screws.
Step 2. Align the adapter with I/O tray slot 9 and insert it; then, press the adapter into the I/O tray until the

connector is fully seated.

Step 3. Tighten the captive thumbscrew on the side of the LOM adapter that secures it to the bracket on

the I/O tray.

If you have no other operations to perform on the I/O tray after installing a LOM adapter in slot 9:

1. Install the riser for slot 10 to 15 (riser 2). See “Install the riser for slot 10 to 15 (riser 2)” on page 220.
2. If any of the adapters in the I/O tray have internal cables, make sure that they are connected before

installing the I/O tray.

3. Install the I/O tray in the chassis and connect all cables. See “Install the I/O tray” on page 154.

Install a PCIe adapter in slot 10 to 15

PCIe adapters in slot 10 to 15 are in an I/O tray riser that is accessed from the rear of the server. With the

riser removed from the I/O tray, open the retention latch and insert the adapter in the riser; then, close the

retention latch.

S002

102

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
110
111
112
113
114
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Aastra Pages: 592

8649 - Eserver xSeries 225

Brand: IBM Pages: 194

AirborneDirect ABDG-SE-IN5410

Brand: Quatech Pages: 8

Brand: NMS Communications Pages: 22

Brand: Cabletron Systems Pages: 100

Brand: Protogate Pages: 30

PRIMERGY CX120 S1

Brand: Fujitsu Pages: 82

PRIMERGY BX922 S2

Brand: Fujitsu Pages: 106

PRIMERGY BX924 S3

Brand: Fujitsu Pages: 290

PRIMERGY BX924 S4

Brand: Fujitsu Pages: 286

PRIMERGY BX924 S3

Brand: Fujitsu Pages: 64

Brand: 3onedata Pages: 24

8-BAY RACKMOUNT NAS

Brand: Seagate Pages: 20

BlackArmor NAS 420

Brand: Seagate Pages: 64

Brand: Inventec Pages: 129

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 74

Brand: Master Digit Pages: 15

SafeNet ProtectServer PCIe HSM

Brand: Gemalto Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands