Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 229 | Manualshive

Page: 229 / 296

background image

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

” on page 89 “

Before you install the riser for slot 1 to 4:

1. Make sure that there is no screw (item 2 in following figure) securing the I/O tray board to the I/O tray in a

location where a captive riser screw will be installed.

2.  Make sure that there are no I/O tray fillers installed in riser slot 1 to 4.
3.  Install adapters in the riser. See “Install a PCIe adapter in slot 1 to 4” on page 99.
4.  If any of the adapters in the riser have internal cables, make sure that they are connected before

installing the riser in the I/O tray.

Complete the following steps to install the riser for slot 1 to 4.

Watch the procedure

. A video of the installation process is available:

•

•

Figure 129. Riser for slot 1 to 4 (riser 1) installation

Step 1. Align the riser with the I/O tray and insert it; then, press the riser into the I/O tray until the connector

is fully seated.

.

Hardware replacement procedures

219

«
...
227
228
229
230
231
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

AMD Opteron LS20 Type 8850

Brand: IBM Pages: 68

NPort IA5250I/5250I-T Series

Brand: Moxa Technologies Pages: 2

Brand: Axel Pages: 28

Brand: Buffalo Pages: 2

SUPERSERVER 1018D-73MTF

Brand: Supero Pages: 124

Force10 MXL Blade

Brand: Dell Pages: 2

Brand: Intel Pages: 69

MFSYS25 - AXXPSU 1000W Power Supply Module

Brand: Intel Pages: 164

Brand: Intel Pages: 226

Brand: Hawking Pages: 2

Brand: Hawking Pages: 37

Edgeline EL4000

Brand: HPE Pages: 57

ProLiant ML110 Gen10

Brand: HPE Pages: 101

ProLiant ML110 Gen10

Brand: HPE Pages: 159

Brand: Bosanova Pages: 2

Usb Peripheral Server/5

Brand: Black Box Pages: 10

Brand: Black Box Pages: 3

Brand: Tibbo Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands