Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 132

Page: 132 / 296

remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

CAUTION:
Make sure that all server power cords are disconnected from their power sources before performing
this procedure.

Before you remove an upper fan cage:

1. Remove the front cover. See “Remove the front cover” on page 131.
2. Remove the upper compute tray or storage tray. See “Remove a compute tray” on page 115 or

“Remove a storage tray” on page 232.

3. If you removed a compute tray and it has one or more compute system boards or a system board filler

installed, remove the system boards or system board filler. See “Remove a system board” on page 109
or “Remove a system board filler” on page 113.

4. Turn the tray upside down.

Complete the following steps to remove an upper fan cage.

Watch the procedure

. A video of the installation process is available:

•

YouTube

•

Youku

122

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands