Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 141

Page: 141 / 296

Figure 69. Front bezel installation

Step 1. Position the bezel on the front of the server.
Step 2. Press and slide the bezel toward the rear of the server until the release tabs engage.

Front cover replacement

Use the following procedures to remove and install the front cover.

Remove the front cover

Remove the front cover by pressing the release buttons and pulling the cover from the front of the server.

Complete the following steps to remove the front cover:

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

Chapter 9

Hardware replacement procedures

131

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands