Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 25 | Manualshive

Page: 25 / 296

background image

•  Requires 4 processors, must be 8100 Series
•  4 processors in a ring topology
•  24 drive bays (including up to 4 NVMe)
•  10 rear PCIe slots
•  Two compute trays, with one system board in each tray
•  Once upgraded, the server will support 12 NVMe drives.

Processor configurations

This configuration requires 4 processors installed in locations 1, 2, 5 and 6.

Figure 7. Processor numbering (viewed from the front of the server)

PCIe slot connectivity

The following table shows the processor to PCIe slot connectivity:

PCIe
slot

Slot location

Description

1

Riser 1

Not connected.

2

Not connected.

.

15

«
...
23
24
25
26
27
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Panasonic Pages: 28

NEAX2000 IVS Series

Brand: NEC Pages: 160

Brand: YOKOGAWA Pages: 22

Brand: SMC Sierra Monitor Pages: 42

Brand: IBM Pages: 66

Netfinity 1000-8477 21Y

Brand: IBM Pages: 268

Express5800/R320f-E4

Brand: NEC Pages: 88

Aspire EASYSTORE H341

Brand: Acer Pages: 59

Aspire EASYSTORE H341

Brand: Acer Pages: 74

Aspire EasyStore Series

Brand: Acer Pages: 148

Aspire easyStore H340

Brand: Acer Pages: 68

Altos EasyStore

Brand: Acer Pages: 169

Aspire easyStore H340

Brand: Acer Pages: 148

Altos EasyStore

Brand: Acer Pages: 7

PowerEdge 400SC

Brand: Dell Pages: 1

Brand: QNAP Pages: 53

Brand: Planet Pages: 95

MultiAccess MULTIACCESS MA30120

Brand: Multitech Pages: 179

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands