Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 147 | Manualshive

Page: 147 / 296

background image

Front USB/VGA assembly replacement

The front USB/VGA assemblys is in the lower compute tray that is accessed from the front of the server.

Remove the front USB/VGA assembly

The front USB/VGA assembly is in the lower compute tray that is accessed from the front of the server. After

removing the lower tray, disconnect the front USB/VGA assembly cables from the lower system board; then,

remove the two screws and remove the operator panel.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

CAUTION:
Make sure that all server power cords are disconnected from their power sources before performing
this procedure.

Before you remove the front USB/VGA assembly:

1.  Remove the front cover. See “Remove the front cover” on page 131.
2.  Remove the lower compute tray. See “Remove a compute tray” on page 115.
3.  If an upper system board or system board filler is installed in the tray, remove it. See “Remove a system

board” on page 109.

4. Remove the lower fan cage. See “Remove a fan cage (lower tray)” on page 123.

Complete the following steps to remove the front USB/VGA assembly.

Watch the procedure

. A video of the installation process is available:

•

•

.

Hardware replacement procedures

137

«
...
145
146
147
148
149
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Samsung Pages: 7

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

Brand: IBM Pages: 214

NetVista N2800e

Brand: IBM Pages: 82

Brand: Atop Pages: 2

Brand: IBM Pages: 140

Brand: Supero Pages: 112

Enterprise Server

Brand: Blackberry Pages: 88

eServer 380 xSeries

Brand: IBM Pages: 112

Brand: Nortel Pages: 144

Brand: NetMedia Pages: 2

Brand: Discover Video Pages: 148

Brand: Thecus Pages: 102

Brand: Digital Watchdog Pages: 7

Blackjack Tower DW-BJST51T Series

Brand: Digital Watchdog Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands