Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 23 | Manualshive

Page: 23 / 296

background image

PCIe
slot

Slot location

Description

1

Riser 1

4

1

Not connected for 2x16. Slots 1 and 2 are not connected if the 2x16 riser is used in
riser slot 1.

2

4

1

Not connected for 2x16. Slots 1 and 2 are not connected if the 2x16 riser is used in
riser slot 1.

3

4

1

4

4

1

5

I/O tray

2

6

2

7

1

8 (ML2)

1

9 (LOM)

1 (PCH)

10

Riser 2

3

2

11

3

2

12

3

2

13

3

2

14

Not connected.

15 (ML2)

Not connected.

16

2x8 Riser

3

2

17

1

M.2

I/O tray

1 (PCH)

Storage
adapter

Upper tray

Not connected.

Storage
adapter

Lower tray

1

Notes:

1. In 2-processor configurations, processors 3 and 4 are not installed; this means slots 1-4, slot 10-13, and slot 16

are not connected.

2. In 3-processor configurations, processor 3 is not installed; this means slot 10-13, and slot 16 are not connected.

Drive bays

Drives are all located at the front of the server, 12 drives at the front of the upper tray and 12 at the front of
the lower tray. Drives are connected to 4-drive backplanes in a 2-by-2 configuration, as shown in the
following figure. All drive bays are 2.5-inch form factor.

Two different drive backplanes are available for the server:

• SAS/SATA backplane: Supports 4 SAS or SATA drives
• AnyBay backplane:

.

13

«
...
21
22
23
24
25
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Enterprise Server S80

Brand: IBM Pages: 282

Brand: Xerox Pages: 40

Brand: GlobalTime Electronic Pages: 19

Brand: 2Wire Pages: 35

Terminal Server

Brand: Black Box Pages: 131

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 74

Express5800/140Hf

Brand: NEC Pages: 482

Brand: Pepperl+Fuchs Pages: 45

Brand: SAP Pages: 32

Brand: 3onedata Pages: 111

Brand: ATEN Pages: 111

Brand: Supero Pages: 91

Brand: Supero Pages: 108

Brand: Supero Pages: 118

Brand: Tektronix Pages: 1026

T4MFCS Scaleout

Brand: VVDN Pages: 37

PowerEdge C6420

Brand: Dell EMC Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands