Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 223 | Manualshive

Page: 223 / 296

background image

•

•

Figure 125. Riser for slot 1 to 4 (riser 1) removal

Step 1. Loosen the two captive screws (items 1 in preceding figure) that secure the riser to the I/O tray

board.

Step 2. Lift the riser up and out of the I/O tray.

After you remove the riser:

• If you are replacing the riser, remove any adapters installed in the riser. See “Remove a PCIe adapter from

slot 1 to 4” on page 92.

• If you are removing the riser and are not installing a replacement:

1. Install the screw that secures the I/O tray board to the I/O tray (item 3 in the figure). This screw

replaces the captive screw on the rear edge of the riser below the midplane connectors. Screw
location is labelled “Remove screw before installing riser” on the I/O board.

2. Install the I/O tray fillers in adapter slot 1 to 4 (item 4 in the figure).
3. Install the I/O tray and connect all cables. See “Install the I/O tray” on page 154.

If you are instructed to return the riser, follow all packaging instructions, and use any packaging materials for
shipping that are supplied to you.

Remove the riser for slot 10 to 15 (riser 2)

The riser for adapter slot 10 to 15 (riser 2) is in the I/O tray that is accessed from the rear of the server. After

removing the I/O tray, loosen the two captive screws that secure the riser to the I/O tray; then, remove the

riser from the I/O tray.

.

Hardware replacement procedures

213

«
...
221
222
223
224
225
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: IBM Pages: 180

Brand: Yeong Yang Pages: 7

Brand: Devolinx Pages: 51

Brand: Lantech Pages: 49

Ultrastar Serv24 S2122-N24-4

Brand: HGST Pages: 36

Brand: IBM Pages: 110

Brand: AIC Pages: 101

Brand: IBM Pages: 220

System x3650 M4 BD Type 5466

Brand: IBM Pages: 786

SUPERSERVER 5018D-MF

Brand: Supero Pages: 120

EonStor GS 3000 Series

Brand: Infortrend Pages: 134

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: Lenovo Pages: 116

Brand: Lenovo Pages: 96

Brand: Lenovo Pages: 46

Brand: Lenovo Pages: 138

Brand: Lenovo Pages: 56

Brand: Lenovo Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands