Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 233 | Manualshive

Page: 233 / 296

background image

” on page 89 “

Attention:

Do

not

use the riser for slot 16 to 17 with four socket storage rich configurations.

Before you install the riser for slot 16 to 17:

1. Make sure that there is no screw (item 2 in following figure) securing the I/O tray board to the I/O tray in a

location where a captive riser screw will be installed.

2.  Make sure that there are no I/O tray fillers installed in adapter slot 16 to 17.
3.  Install adapters in the riser. See “Install an I/O adapter in slot 16 to 17” on page 104.
4.  If any of the adapters in the riser have internal cables, make sure that they are connected before

installing the riser in the I/O tray.

Complete the following steps to install the riser for slot 16 to 17.

Watch the procedure

. A video of the installation process is available:

•

•

Figure 132. Riser for slot 16 to 17 installation

Step 1. Align the riser with the I/O tray, making sure that the sides of the riser fit into the guides on the I/O

tray, and insert the riser; then, press the riser into the I/O tray until the connector is fully seated.

Step 2. Tighten the captive screw (item 4 in preceding figure) that secures the riser to the I/O tray board.

If you have no other operations to perform on the I/O tray after installing the riser for slot 16 to 17, install the I/
O tray in the chassis and connect all cables. See “Install the I/O tray” on page 154.

.

Hardware replacement procedures

223

«
...
231
232
233
234
235
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: LaCie Pages: 4

x3655 - System - 7985

Brand: IBM Pages: 118

Brand: HPE Pages: 174

IntelliStation R Pro

Brand: IBM Pages: 194

Brand: Fibrenetix Pages: 17

A+ AS-2124US-TNRP

Brand: Supermicro Pages: 130

Brand: Supermicro Pages: 118

callpilot 1002rp

Brand: Avaya Pages: 150

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: QNAP Pages: 69

Brand: Silex technology Pages: 2

Brand: MAXDATA Pages: 2

Brand: MAXDATA Pages: 6

Brand: Promise Technology Pages: 2

SocketEthernetIP EN60601

Brand: Multitech Pages: 2

NETWORK PROXY 5.3.0 -

Brand: Red Hat Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands