Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 277 | Manualshive

Page: 277 / 296

background image

Appendix A. Hardware disassembling for recycle

Follow the instructions in this section to recycle components with compliance with local laws or regulations.

Disassemble the system board for recycle

Follow the instructions in this section to disassemble the system board before recycling.

Before disassembling the system board:

1. Remove the system board from the server (see “Remove a system board” on page 109).
2. Refer to local environmental, waste or disposal regulations to ensure compliance.

Complete the following steps to disassemble the system board:

Step 1. Remove the following components as illustrated:

• Use a Torx T10 screwdriver and remove the Torx T10 screw (

1

in the following illustration)

• Use a screwdriver and remove the 9 screws

Figure 151. Disassembling the system board

© Copyright Lenovo 2020

267

«
...
275
276
277
278
279
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

RS/6000 7043 43P Series

Brand: IBM Pages: 322

System x3400 M3 Types 7378

Brand: IBM Pages: 45

e Server iSeries 825

Brand: IBM Pages: 52

Brand: Hi-flying Pages: 29

Brand: NEC Pages: 408

Brand: Pathos Acoustics Pages: 26

Brand: AXIOMTEK Pages: 58

Brand: Altos Pages: 104

Brand: Speco Pages: 28

Brand: BRONKHORST Pages: 19

Brand: Asus Pages: 186

Brand: QNAP Pages: 58

Brand: Polycom Pages: 11

Brand: ADLINK Technology Pages: 62

Brand: Black Box Pages: 4

Brand: Black Box Pages: 12

NETWORK SATELLITE 5.3.0 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 318

Express5800/140Hf

Brand: NEC Pages: 482

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands