Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 120 | Manualshive

Page: 120 / 296

background image

The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

” on page 89 “

CAUTION:
Make sure that all server power cords are disconnected from their power sources before performing
this procedure.

Before you remove the system board:

1.  Remove the front cover. See “Remove the front cover” on page 131.
2.  Remove compute tray where the system board is installed. See “Remove a compute tray” on page 115.
3.  If you are removing the lower system board in a compute tray, first remove the upper system board or

filler from the compute tray to access connectors on the lower system board. See the steps below or
“Remove a system board filler” on page 113.

Complete the following steps to remove the compute system board:

Watch the procedure

. A video of the replacement process is available:

•

•

Figure 55. System board removal

Step 1. Disconnect all cables on the system board that go to connectors in the compute tray. See “Internal

cable routing” on page 40.

Step 2. Press the release clips and slide the system board out of the compute tray.

After you remove the system board:

110

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
118
119
120
121
122
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Jung Pages: 16

Brand: TYAN Pages: 136

Brand: IBM Pages: 21

FusionServer XH321 V5

Brand: xFusion Digital Technologies Pages: 76

Brand: Infrant Technologies Pages: 98

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: QNAP Pages: 16

G4-20G-010-192T

Brand: Viavi Pages: 12

Brand: Super Pages: 60

DeviceMaster PRO

Brand: Comtrol Pages: 174

LANTIME M600/GPS

Brand: Meinberg Pages: 6

ProxyServer MTPSR1-202ST

Brand: Multitech Pages: 142

Brand: Dell EMC Pages: 25

Brand: Dell EMC Pages: 184

Brand: Intel Pages: 74

Brand: Riva Pages: 20

Brand: Russound Pages: 48

Brand: Gigabyte Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands