Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 184

Page: 184 / 296

Figure 96. Memory module locations

Complete the following steps to remove a memory module.

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

Step 1. Open the memory module connector retaining clips to extract the memory module; then, remove

the memory module.

If you are not replacing the memory module that you removed:

1. See

the

Memory Population Reference

for the required installation order of the remaining memory

modules.

2. Install a memory module filler, that was originally provided with the PHM option, in any vacant memory

module connectors.

3. Install the upper system board or system board filler, if it was removed. See “Install a system board” on

page 111.

4. Install the compute tray where the system board is installed. See “Install a compute tray” on page 117.

174

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands