Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 198 | Manualshive

Page: 198 / 296

background image

Note 1:

For power source redundancy, the power supplies in bays 1 and 3 must be fed from a different

power source than the power supplies in bays 2 and 4.

–

“yes/no” means the system will remain operating if the power input to bays 2 and 4 fails.

–

“no/yes” means the system will remain operating if the power input to bays 1 and 3 fails.

Before you install a power supply:

1. If the power supply bay contains a filler, pull the filler from the bay.

Complete the following steps to install a power supply:

Watch the procedure

. A video of the installation process is available:

•

•

Step 1. Install the power supply in the bay.

Figure 103. Power supply installation

Insert the power supply in its bay and press it in until the release tab locks.

After you have installed a power supply:

1. Connect the power cable to the power supply.
2. Route the power cable through the cable hook-and-loop on the rear of the server so that it does not

accidentally become unplugged.

Remove a power supply filler

Remove a power supply filler by pulling the filler from the bay.

Complete the following steps to remove a power supply filler:

188

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
196
197
198
199
200
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Altos R700 Series

Brand: Acer Pages: 80

Altos G700 series

Brand: Acer Pages: 14

Brand: Acer Pages: 103

Altos R720 Series

Brand: Acer Pages: 104

Brand: KYLAND Pages: 30

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

AirLive WP-203G

Brand: Ovislink Pages: 132

Transport TX46 (B4985) Service

Brand: TYAN Pages: 75

System x3650 M4 BD Type 5466

Brand: IBM Pages: 786

SUPERSERVER 5015M-MF

Brand: Supero Pages: 120

Brand: Brocade Communications Systems Pages: 176

RIP Station 5100

Brand: Epson Pages: 140

Brand: Huawei Pages: 2

Brand: Huawei Pages: 52

Brand: Huawei Pages: 122

Brand: Huawei Pages: 131

UPS5000-E-****-FM series

Brand: Huawei Pages: 261

Brand: NEC Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands