ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 72

Page: 72 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

• Check the pump power.

If the pump performance does not satisfy your process requirements, and the process
requirements have not changed, then perform these steps:

1. Disassemble the pump.
2. Inspect it.
3. Replace worn parts.

Bearing maintenance

These bearing lubrication sections list different temperatures of the pumped fluid. If the

pump is ATEX-certified and the temperature of the pumped fluid exceeds the permitted
temperature values, then consult your ITT representative.

Bearing lubrication schedule

Type of bearing

First lubrication

Lubrication intervals

Oil-lubricated bearings

Add oil before you install and start
the pump. Change the oil after
200 hours for new bearings.

After the first 200 hours, change
the oil every 1000 operating hours
or every two months.

Grease-lubricated bearings

Grease-lubricated bearings are in-
itially lubricated at the factory.

Regrease bearings every 500 op-
erating hours or every month.

Lubricating oil requirements

Use a high quality turbine oil with rust and oxidation inhibitors.
You can use an oil of ISO viscosity grade VG 220 (SAE grade 50W) for all bearing operation
temperature ranges.

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands