ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 25 | Manualshive

Page: 25 / 160

background image

Installation

XHD Installation, Operation, and Maintenance Manual

23

d) Make sure that the center jackscrews do not touch the foundation surface yet.

Item Description

1.

Jackscrew

2.

Baseplate

3.

Foundation

4.

Plate

Figure 13: Jackscrews

3. Level the driver mounting pads:

NOTICE:
Remove all dirt from the mounting pads in order to ensure that the correct leveling is
achieved. Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.
b) Put the other machinist's level across the ends of the two pads.
c) Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both
lengthwise and across.
Use the baseplate-leveling worksheet when you take the readings.

Item Description

1.

Machinist's levels

2.

Driver's mounting pads

3.

Foundation bolts

4.

Jackscrews

5.

Grout hole

6.

Pump's mounting pads

Figure 14: Level driver mounting pads

4. Turn the center jackscrews down so that they rest on their plates on the foundation surface.
5. Level the pump mounting pads:

«
...
23
24
25
26
27
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: DAB Pages: 8

Brand: Navien Pages: 108

Brand: Ultranatura Pages: 24

Brand: York International Pages: 87

Brand: valent Pages: 20

Brand: A.O. Smith Pages: 2

PC 3010 NT VARIO o.C.

Brand: vacuubrand Pages: 92

Brand: A.O. Smith Pages: 76

Brand: York Pages: 72

Brand: MULTIQUIP Pages: 35

Brand: BA Pumps & Sprayers Pages: 18

Brand: FTI Pages: 9

ProMax Pressure Well 6500/10

Brand: Oase Pages: 180

Brand: Dimplex Pages: 24

aroSTOR VWL B 270/5

Brand: Vaillant Pages: 240

Optyma Plus INVERTER Series

Brand: Danfoss Pages: 54

InverterFlex B-VFH09MA-1

Brand: COMFORT-AIRE Pages: 24

Brand: evosanitary Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands