ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 92

Page: 92 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

1. Remove the two-piece suction and discharge flanges (195C, XHD sizes 150 and above

only).

Figure 72: Joint gaskets and flanges removal

Remove the suction half casing - Rubber-Lined

The following parts remain attached to the suction half casing when it is removed from the rest
of the pump wet end:

Model

Parts that are still attached

XHD Rubber-lined single piece suction liner

• Suction side liner (600R)
• Hardware Hex head bolts/hex cap screws

1. Support the suction half casing (100A) with a hoist hook through the lifting lug. Tension the

hoist properly so the sub-assembly will be fully supported upon disengagement.

2. Remove the casing hex head nuts (600C) and flat washers (553) from the casing hex head

bolts (600A) and tapered alignment studs (600D).

3. Leave the tapered alignment studs (600D) secured in place. The studs will provide

guidance in removal of the sub-assembly.

4. Guide the suction half casing (100A, with attached components) free of tapered alignment

studs.

Figure 73: Gland and suction liner

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands