ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 121

Page: 121 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

119

Figure 113: Attachment of stuffing box to seal cover

4. Trim edges of the stuffing box gasket such that they will not interfere with the stuffing box

oring.

5. Lubricate and install the seal cover-to-stuffing box o-ring (496R) into the seal cover (184).
6. Attach the stuffing box (159) to the seal cover (184) using the stuffing box-to-seal cover hex

head cap screws (569L).

Figure 114: Split Stuffing box installation

Install the expeller (optional feature)

1. With the power frame and shaft moved forward so the expeller locating turn is accessible

on the shaft; install the expeller (263) onto the shaft (122).

2. Prepare the impeller hub o-ring (412U) with a lubricant and install the o-ring into the o-ring

groove on the expeller (263).

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands