ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 8 | Manualshive

Page: 8 / 160

background image

Introduction and Safety

XHD Installation, Operation, and Maintenance Manual

6

Hazard level

Indication

WARNING:

A hazardous situation which, if not avoided,
could result in death or serious injury

CAUTION:

A hazardous situation which, if not avoided,
could result in minor or moderate injury

NOTICE:

• A potential situation which, if not avoided,

could result in undesirable conditions

• A practice not related to personal injury

Hazard categories

Hazard categories can either fall under hazard levels or let specific symbols replace the
ordinary hazard level symbols.
Electrical hazards are indicated by the following specific symbol:

Electrical Hazard:

These are examples of other categories that can occur. They fall under the ordinary hazard
levels and may use complementing symbols:

• Crush hazard

• Cutting hazard

• Arc flash hazard

Environmental safety

The work area

Always keep the station clean to avoid and/or discover emissions.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

• Appropriately dispose of all waste.

• Handle and dispose of the processed liquid in compliance with applicable environmental

regulations.

• Clean up all spills in accordance with safety and environmental procedures.

• Report all environmental emissions to the appropriate authorities.

WARNING:
If the product has been contaminated in any way, such as from toxic chemicals or nuclear
radiation, do NOT send the product to ITT unless it has been properly decontaminated.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

Recycling guidelines

Always follow local laws and regulations regarding recycling.

«
...
6
7
8
9
10
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: DAB Pages: 8

geoTHERM SERIES

Brand: Vaillant Pages: 112

geoTHERM SERIES

Brand: Vaillant Pages: 132

Brand: XPOtool Pages: 10

Brand: Navien Pages: 83

Brand: INOXPA Pages: 20

POWERMASTER III

Brand: Lincoln Pages: 6

Brand: KISANKRAFT Pages: 44

SBC 1100 ADV PLUS FR

Brand: Quick Pages: 76

Brand: hajdu Pages: 132

Brand: Econo Pages: 27

Brand: Flux Pages: 80

Brand: Oase Pages: 42

Brand: Unico Pages: 48

Brand: EBARA Pages: 18

Brand: AL-KO Pages: 140

Brand: Heat Controller Pages: 15

DYNAMIC-SS/X8/C

Brand: HydroTherm Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands