ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 12 | Manualshive

Page: 12 / 160

background image

Introduction and Safety

XHD Installation, Operation, and Maintenance Manual

10

Equipment for monitoring

For additional safety, use condition-monitoring devices. Condition-monitoring devices include
but are not limited to these devices:

• Pressure gauges

• Flow meters

• Level indicators

• Motor load readings

• Temperature detectors

• Bearing monitors

• Leak detectors

• PumpSmart control system

Product approval standards

Regular standards

WARNING:
Use of equipment unsuitable for the environment can pose risks of ignition and/or explosion.
Ensure that the code classifications on the pump are compatible with the specific environment
in which the equipment is to be installed. If they are not compatible, do not operate the
equipment and contact an ITT representative before proceeding.

All standard products are approved according to CSA standards in Canada and UL standards
in USA. The drive unit degree of protection follows IP68. See the nameplate for maximum
submersion, according to standard IEC 60529.
All electrical ratings and performance of the motors comply with IEC 600341.

Explosion-proofing standards

All explosion-proof products for use in explosive atmospheres are designed in compliance with
one or more of the following approvals:

• EN, ATEX Directive 94/9/EC

• FM According to NEC

• Class 1 Div 1 Groups “C”, and “D”

• Class 2 Div 1 Groups “E”, “F”, and “G”

• Class 3 Div 1 Hazardous Locations

ATEX/IECEx:

• Group: IIC

• Category: 2 or 3

• Temperature Class: T4 (for ambients up to 100ºC)

• ATEX Marking: Ex II 2 G

CSA certification

Intrinsically safe for:

• Class I, Div. 1, Groups A, B, C, D

• Class II, Div. 1, Groups E, F, G

• Class III

«
...
10
11
12
13
14
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: A.O. Smith Pages: 77

Brand: Quantum Pages: 20

Brand: Danfoss Pages: 20

Fybroc series 1530

Brand: Met-Pro Pages: 22

Brand: Nortek Pages: 52

Brand: Speck Pages: 24

Brand: Pentair Pages: 16

Brand: Remco Pages: 5

MD 12C NT VARIO o.C.

Brand: vacuubrand Pages: 92

Brand: AME Pages: 6

Brand: STIEBEL ELTRON Pages: 56

Brand: Elnur Pages: 7

Pneumatic grease pump 50:1

Brand: Pressol Pages: 14

Brand: Pfeiffer Vacuum Pages: 56

GU145/508111145

Brand: Eternal Pages: 56

Whale Expanse DW0801U

Brand: Munster Simms Engineering Ltd. Pages: 27

FlowFriend HFP90

Brand: Air-Aqua Pages: 14

Brand: Godiva Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands