ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 120

Page: 120 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

118

5. Install the hex head capscrews (370Y) through the pedestal flange into the gland half

casing (100D) to complete assembly.

Figure 111: Capscrew installation through pedestal flange into gland half casing

Stuffing box assembly and installation

Pump model

Next step to follow

XHD Value Option

• Go to Install the seal cover instructions.

XHD

• You will need to assemble the two split stuffing

box halves before attaching the stuffing box to
the seal cover. Start with the next step, Assem-
ble the split stuffing box.

Install the seal cover

1. Lubricate and install the seal cover-to-casing volute liner gasket (351Q) onto the seal cover

(184).

2. Attach the seal cover (184) to the gland half casing (100D) using the seal cover retention

socket head cap screws (388A) and clipped washers (354A).

Figure 112: Seal cover installation

Assemble the split stuffing box - XHD

1. Position the flat gaskets (367B) between the two halves of the split stuffing box (159).
2. Assemble the two halves of the split stuffing box (with gaskets in place) using the stuffing

box shoulder bolts (328). Apply a liberal coating of silicone sealant to both faces of the split
stuffing box before the gasket is installed.

3. Attach the stuffing box (159) to the seal cover (184) using the stuffing box-to-seal cover hex

head cap screws (569L).

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands