ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 91 | Manualshive

Page: 91 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

89

NOTICE: Item (412A) Impeller O-ring is supplied only with the metal impeller.

Figure 70: Removal of shaft sleeve

Disassembly for Rubber-Lined

The disassembly steps for Metal-lined and Rubber-lined differ. This section, beginning with
Typical disassembly and ending with Remove the shaft sleeve, pertains to Rubber-lined
pumps.
For Metal-lined pumps, refer to the sub-section,

Disassembly for Metal-Lined

Disassembly - Rubber-Lined

The XHD Rubber lined slurry pump is currently available only with the single piece non-
adjustable suction seal ring.
The suction half casing and attached components can be removed for further disassembly and
replacement of the suction side liner (600R) as necessary. After removing the impeller (101) by
disengaging the knock-off ring (149), the gland half casing (100D) can remain mounted to the
pedestal (131) and the casing gland side liner (600T) removed for replacement. Other
components such as the gland, packing, seal cover etc. can also be removed in a methodical
fashion as needed for inspection and replacement.

Figure 71: Gland and Suction Liner

Remove the joint gaskets and flanges - Rubber-Lined

NOTICE: Gaskets 351A and 351B are supplied only with metal lined pumps. Gaskets for
rubber lined pumps are integral with rubber liners.

«
...
89
90
91
92
93
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: vacuubrand Pages: 44

Brand: Jandy Pages: 108

Brand: York Pages: 27

Brand: York Pages: 32

iSOLAR PDP Series

Brand: ICON Pages: 24

ZHHS-01-10K-R290-V5-M

Brand: JBG HT Pages: 32

Brand: Daikin Pages: 26

Brand: Rheem Pages: 28

Brand: Mueller Pages: 46

Brand: Watts Pages: 24

Brand: Daikin Pages: 284

Warren Rupp SANDPIPER Beast SPB20

Brand: Idex Pages: 21

Brand: T.I.P. Pages: 72

Brand: DAE Pumps Pages: 29

EIWH electronicVED pro Series

Brand: Vaillant Pages: 12

Brand: Buhler Pages: 48

Brand: Walrus Pages: 6

Brand: emaux Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands