ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 106 | Manualshive

Page: 106 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

104

NOTICE: A tapped hole is provided in the coupling end of the shaft, to allow for vertical
assembly and disassembly of the power frame components. This will provide a location to
hold the shaft and withdraw from the frame in the vertical position.

Figure 93: Power frame disassembly

Once the outboard bearing end cover related components are removed, the shaft can be
withdrawn from the frame while in the vertical position.

5. Remove the inboard bearing cover assembly hex head capscrews (370P).
6. Remove the inboard bearing cover (119) from the bearing cartridge housing (228) with the

o-ring (412), labyrinth seal (333A) and shims (390C) still installed.

7. Remove the inboard labyrinth seal (333A) and o-ring (412).

Figure 94: Removal of labyrinth seal

8. Slide the rotating element assembly from the bearing cartridge housing (228), using the

lifting hoist in the coupling end of the shaft to retract the assembly from the frame. Lifting
hole sizes are specified below.

Pump Size

Frame Size

Shaft lifting hole thread size

XHD50, XHD75

PF1

M16 x 2

XHD80

PF2

M16 x 2

XHD100, XHD125

PF3

M16 x 2

XHD150

PF4/PF4S

M24 x 3

XHD200

PF4/PF4S

M24 x 3

XHD250

PF5

M24 x 3

XHD300

PF5

M24 x 3

«
...
104
105
106
107
108
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: EBARA Pages: 16

Brand: EBARA Pages: 40

Brand: EBARA Pages: 38

Brand: vacuubrand Pages: 24

Brand: Zodiac Pages: 23

Brand: Calpeda Pages: 27

Brand: Watts Pages: 12

Brand: Nibe Pages: 44

Brand: Wilo Pages: 80

SMART GEYSER 2330-03

Brand: Simer Pages: 12

Brand: Ducar Pages: 30

Brand: Xylem Pages: 21

Brand: Marco Pages: 3

Brand: Trinity Lx Pages: 24

UNIBLOC-PD Series

Brand: Unibloc-Pump Pages: 53

Brand: Maytag Pages: 12

Brand: Wilo Pages: 32

York YH9FYH12BAH-A-X

Brand: Johnson Controls Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands