ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 57

Page: 57 / 160

Commissioning, Startup, Operation, and Shutdown

XHD Installation, Operation, and Maintenance Manual

Item Description

Nut

Washer

Bolt

Figure 37: Secure coupling guard half to end plate

5. Put the driver half of the coupling guard in place:

a) Slightly spread the bottom apart.
b) Place the driver half of the coupling guard over the pump half of the coupling guard.

The annular groove in the coupling guard half must face the motor.

6. Place the driver-side end plate over the motor shaft.
7. Place the driver-side end plate in the annular groove of the driver-half of the coupling

guard.

8. Use a bolt, a nut, and two washers to secure the coupling guard half to the end plate. Hand-

tighten only.
The hole is located on the driver-side of the coupling guard half.

9. Slide the driver-half of the coupling guard towards the motor so that the coupling guard

completely covers the shafts and coupling.

10. Use a nut, a bolt, and two washers to secure the coupling guard halves together.
11. Tighten all nuts on the guard assembly.

Bearing lubrication

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure

bearings are properly lubricated prior to startup.

NOTICE:
Grease can settle in equipment left idle leaving bearings improperly lubricated. Check the
greasing on a pump that has been out of service for a long period of time and re-grease if
necessary.

Pumps are shipped without oil. You must lubricate oil-lubricated bearings at the job site.
Grease-lubricated bearings are lubricated at the factory.

Lubricate the bearings with oil

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure

bearings are properly lubricated prior to startup.

1. Remove the oil fill pipe plug (319B).
2. Fill the bearing frame with oil through the filler connection that is located on the top of the

bearing frame.

3. Fill the bearing frame with oil until the oil level reaches the middle of the sight glass or

opposite sight glass (319 or 408N). The correct volume of oil required for each size of

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands