ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 126 | Manualshive

Page: 126 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

124

9. Install the seal ring hex jam nuts (357B) on the square head adjusting bolts (356F) that now

protrude from the suction half casing (100A). Fully tighten to complete assembly.

Figure 121: Suction liner installation

10. Coat the volute liner-to-suction side liner flat gasket (351N) with lubricant and install into

the suction side liner (561).

11. Install the suction side liner holding threaded rob and nut (372N, sizes 150 and above

only).

Reassembly for Rubber-Lined

The reassembly steps for Metal-lined and Rubber-lined differ. This section, beginning with
Install the casing volute liner and ending with Install suction half casing with other suction half
components attached, pertains to Rubber-lined pumps.
For Metal-lined pumps, refer to the sub-section,

Reassembly for Metal-Lined

Install the casing volute liner - Rubber-lined

NOTICE: When the Dynamic Seal option is provided, be sure the power end and expeller
assembly are adjusted prior to volute liner installation so that the expeller does not interfere
with the installation of the volute liner.

1. Coat the threads of the casing volute liner retention studs (600L) that will be inserted into

the casing volute liner (600T) with anti-seize compound.

«
...
124
125
126
127
128
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: Danfoss Pages: 72

Brand: Danfoss Pages: 91

DHP-H Varius Pro+

Brand: Danfoss Pages: 12

Brand: vacuubrand Pages: 24

607 challenger series

Brand: National Vacuum Equipment Pages: 20

Brand: Quantum Pages: 20

Brand: Wayne Pages: 8

Brand: Wayne Pages: 20

Brand: Wayne Pages: 8

Brand: Wayne Pages: 12

Brand: Walrus Pump Pages: 8

BC-F20HWR2-200L

Brand: enertik Pages: 33

Brand: Fairland Pioneer Pages: 36

Brand: SAER Elettropompe Pages: 44

Brand: Lumax Pages: 28

Oberdorfer 800B

Brand: Gardner Denver Pages: 2

Brand: Watson-Marlow Pages: 12

Brand: Winston Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands