ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 88 | Manualshive

Page: 88 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

86

3. Hoist the casing assembly to the ground so that the seal cover or stuffing box cover can be

removed.

Figure 63: Seal cover removal

4. Remove the seal cover retention hex head cap screws (388A) and clipped washers (354A).
5. Remove the seal cover (184) from the gland half casing (100D). Use a short pry bar to

gently and evenly facilitate disassembly if necessary.

6. Remove the seal cover o-ring (496R, XHD).

Optional disassembly of gland half casing, volute liner, and seal cover - Metal-Lined

NOTICE: When there is no expeller assembly supplied, the Gland casing assembly can be
removed and rebuilt as an assembly.

The gland half casing (100D), volute liner (561), seal cover (184), and/or split stuffing box
assembly (159), can be removed as an entire assembly
1. Once the impeller is removed from the shaft, support the entire gland casing assembly with

a strap, located thru the appropriate gland half casing hoisting location.

2. Loosen and remove the casing to pedestal bolts (370Y) and nuts from the taper alignment

studs (427L).

3. Carefully remove the assembly and hoist to the ground to disassemble as required, using

the instructions in the related sections of this instruction manual.

Figure 64: Removal of gland half casing

«
...
86
87
88
89
90
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: Danfoss Pages: 40

Brand: vacuubrand Pages: 24

Brand: ULTIMATE SPEED Pages: 52

DynaDrive DD60-10

Brand: Davey Pages: 32

Brand: Xylem Pages: 8

Brand: BIANCO PUMPZ Pages: 12

Brand: Alto Pages: 17

Brand: fluid-o-tech Pages: 4

Brand: Carrier Pages: 16

Brand: A.O. Smith Pages: 35

Brand: Cleveland Pages: 2

Brand: ICP Pages: 17

Myers ME40 Series

Brand: Pentair Pages: 12

Brand: AL-KO Pages: 186

Brand: Viessmann Pages: 124

Brand: Xylem Pages: 2

Brand: Danner Pages: 2

Brand: Calpeda Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands