ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 125

Page: 125 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

123

3. Lubricate and install the volute liner-to-suction side liner gasket (351N).

Figure 119: Suction side liner into suction half casing - metal lined

After completion, skip the next step listed for the XHD and move onto the Install the suction half
casing step.

Install adjustable seal ring and suction side liner into suction half casing - XHD

1. Coat the seal ring ID o-rings (512A) and OD o-rings (512B) with lubricant and install into the

adjustable seal ring (822).

2. Install the seal ring indicator roll pin (757A) into the adjustable seal ring (822).
3. Align the three evenly spaced tapped holes in the adjustable seal ring (822) with the three

thru-holes of the suction side liner (562).

4. Slide the adjustable seal ring into the suction side liner (562) slowly, keeping the holes

aligned while being care not to damage or shear the seal ring OD o-rings (512B).

5. Install the seal ring adjusting bolt onto the adjusting bolts (356F).

Figure 120: Seal ring installation

6. Coat the non-driving end threads of the square head adjusting bolts (356F) with an anti-

seize compound and insert through the suction side liner into the tapped holes of the seal
ring.

7. Tighten the square head adjusting bolts (356F) fully using a metric driver. This will fully seat

the adjustable seal ring (822) in the suction side liner (562).

8. Using proper support, life the suction side liner (562) with the adjustable seal ring (822)

installed into position and insert into the suction half casing, using the square head
adjusting bolts (356F) as a guide.

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands