ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 82

Page: 82 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

6. Remove the tapered alignment studs (600D) from the gland half casing (100D) using a

metric stud driver.

Figure 53: Casing bolt removal

Remove the remaining suction half components - Metal-Lined

Pump model

Next step to follow

XHD

• Remove the suction side liner and adjustable

seal ring

• Remove the adjustable seal ring

XHD Value Option

• Remove the suction liner

Remove suction side liner - XHD Value Option - Metal-Lined

1. Remove the suction side liner retention nuts (357A).
2. Remove suction side liner (562) from suction half casing (100A).
3. Remove the suction side liner retentions studs (356E) from the suction side liner (562)

using a metric stud driver.

4. Remove the suction side liner flat gasket (351N).

Figure 54: Removal of suction side liner - metal lined

Remove the suction side liner and adjustable seal ring - XHD - Metal-Lined

1. Remove the jam nuts (357A) that attach the adjustable seal ring (822) and the suction side

liner (562) to the suction half casing (100A).

2. Remove the suction side liner holding bolts (372N, XHD sizes 150 and above only).

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands