ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 105 | Manualshive

Page: 105 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

103

6. Remove the bearing frame adjustment plate bolts (352G), nuts (427D) and bearing frame

adjustment plates (234F).

Figure 91: Removal of bearing frame hardware

7. Tension the hoist fully to lift and move the power end to designated work area.

Figure 92: Lifting of power end

Disassemble the power end - XHD, oil lubrication

1. Remove the outboard bearing cover assembly hex head capscrews (370N).
2. Remove the outboard bearing cover (109) from the bearing cartridge housing (228) with the

o-ring (412) and labyrinth seal (332A) still installed.

3. Remove the outboard labyrinth seal (332A) and o-ring (412).
4. Remove the Bellville preload washer (529).

Important: Always remove the outboard bearing cover assembly and Bellville washer first.
This will remove the preload from the rotating element assembly for easier removal of the
remaining bearing frame components.

«
...
103
104
105
106
107
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: TANKLESS Pages: 72

Brand: salmson Pages: 12

Brand: Kärcher Pages: 8

Brand: Tandem Pages: 120

Brand: vacuubrand Pages: 76

Brand: Becker Pages: 5

Brand: John Wood Pages: 28

PERFECT 350 ELECTRONIC

Brand: Wijas Pages: 9

Summit Pumper Vacuum

Brand: Alto Pages: 6

Brand: Hi-Force Pages: 16

Brand: Ocean Aire Pages: 36

Brand: Wacker Neuson Pages: 42

Brand: T.I.P. Pages: 134

Brand: Bock Water heaters Pages: 62

Brand: C.P.A. Pages: 40

Brand: HARNITEK Pages: 28

Brand: Laars Pages: 20

Cylinder DuroTech MAP07

Brand: Milwaukee Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands