ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 101

Page: 101 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

3. Carefully remove the assembly and hoist to the ground to disassemble as required, using

the instructions in the related sections of this instruction manual.

Figure 84: Removal of gland half casing

Figure 85: Gland half casing disassembly

Locate and lift the volute liner for optional discharge locations (field
replacement) - Rubber-Lined

1. The Volute Liner (600T) can be installed into the Gland Casing (100D) the field in any of the

optional discharge orientations.

2. Remove the Suction casing and Suction Liner assembly as described in the section

'Remove the Suction Side.

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands