ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 83 | Manualshive

Page: 83 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

81

3. Move the suction side liner (562) with adjustable seal ring (822) inside free from the suction

half casing (100A).

4. Remove the suction side liner front gasket (351N).

Figure 55: Removal of Suction liner (Metal Lined)

Suction side liner holding bolts on XHD sizes 150, 200, 250 and 300 only.

Remove the adjustable seal ring - XHD - Metal-Lined

1. Slide the adjustable seal ring (822) free from the suction side liner (562).
2. Remove the square head adjusting bolts (372N) from the adjustable seal ring.
3. Remove the seal ring inner diameter o-rings (512A) and outer diameter o-rings (512B). The

indicating roll pin (757A) can also be removed if necessary.

Figure 56: Removal of adjustable seal ring - metal lined

Impeller removal - Metal-Lined

Two people should work together to remove the impeller for safety purposes.
1. Remove the gland assembly halves (107) by removing the gland adjusting bolts (353).
2. Loosen the bearing frame adjustment plate bolts (352G) and nuts (427D) but DO NOT

remove hardware or adjustment plates (234F). Keep hardware finger-tight to keep the
bearing frame constrained to the pedestal while allowing it to slide along the pedestal rails.

3. Slide the bearing housing and shaft assembly forward towards the suction side of the pump

to allow better access to the impeller (101).

4. Remove the two-piece knock-off ring (149).

«
...
81
82
83
84
85
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: JAMA Pages: 55

Brand: Tebas Pages: 14

Brand: Barnstead|Thermolyne Pages: 56

Brand: Rinnai Pages: 67

Q HEAT R Series

Brand: CANVAC Pages: 88

Altherma 3 M Series

Brand: Daikin Pages: 24

Brand: German pool Pages: 11

GPVX 75L Series

Brand: A.O. Smith Pages: 52

Brand: Samoa Pages: 38

Brand: FE PETRO Pages: 16

Fillcontrol Auto Compact

Brand: Reflex Pages: 17

Brand: DAB Pages: 228

Brand: Bard Pages: 26

LARIUS VEGA 5:1

Brand: Samoa Pages: 28

Brand: Seisco Pages: 20

Brand: Asada Pages: 28

Brand: Warren rupp Pages: 13

Brand: Tacmina Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands