ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 53 | Manualshive

Page: 53 / 160

background image

Commissioning, Startup, Operation, and Shutdown

XHD Installation, Operation, and Maintenance Manual

51

V-belt drive monitoring and protection

1. Use all of the information in these sections to ensure that the v-belt drive is properly

installed for correct operation and long life.

2. Keep the v-belts clean. Exposure to dirt and grease can reduce belt life. Maintaining a

clean drive is the one of the best practices a user can employ to ensure drive longevity.

3. Always follow safety procedures. Never adjust any components of the v-belt drive while the

unit is in operation.

4. Always observe v-belt running operation through the mesh portions of the drive guard at a

safe distance.

5. Always keep all appendages, clothing, and site tooling out of reach while the drive is

running. Failure to do so could result in personal injury and unit damage.

6. Never run the unit without the drive guard in place.

Figure 31: Pump with OHMM and belt guard installed

Couple the pump and driver

WARNING:
Failure to disconnect and lock out driver power may result in serious physical injury or death.
Always disconnect and lock out power to the driver before performing any installation or
maintenance tasks.

• Electrical connections must be made by certified electricians in compliance with all

international, national, state, and local rules.

• Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for

specific instructions and recommendations.

Couplings must have proper certification to be used in an ATEX classified environment. Use
the instructions from the coupling manufacturer in order to lubricate and install the coupling.
Refer to driver/coupling/gear manufacturers IOM for specific instructions and recommenda-
tions.

«
...
51
52
53
54
55
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Elmo Rietschle V-VC 40

Brand: Gardner Denver Pages: 32

Brand: Grundfos Pages: 16

GARLAND GEISER 401 Q

Brand: Productos McLand Pages: 92

Boostamatic 4000

Brand: Stuart Pages: 20

Brand: Elkay Pages: 2

Brand: Alpine Pages: 20

Flame Guard Safety System

Brand: American Water Heater Pages: 29

Brand: Geotech Pages: 32

Brand: SPERONI Pages: 68

Optyma Slimpack OP-LSQM Series

Brand: Danfoss Pages: 174

Brand: Trane Pages: 8

Brand: Red Jacket Pages: 42

Brand: T.I.P. Pages: 136

FLOJET R4320143A

Brand: Xylem Pages: 38

Brand: Grundfos Pages: 8

HAWK LEUCO TXT Series

Brand: Kärcher Pages: 36

Aquamax ECO 4000

Brand: Oase Pages: 43

Brand: Boreal Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands