ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 128 | Manualshive

Page: 128 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

126

4. Secure the casing volute liner (600T) to the gland half casing (100D) by installing and fully

tightening the volute liner retention hex nuts (355C).

Install the impeller - Rubber-Lined

Two (2) people should work together to install the impeller for safety purposes.
1. Loosen the adjustment plate bolts (352G) and nuts (427D) but DO NOT remove bolts or

adjustment plates (234F). Bolts should remain finger-tightened to keep rotating assembly
constrained to the pedestal.

Figure 124: Adjustment plate bolting installation

2. Slide the power end forward towards the suction side of the pump to allow better access to

the shaft (122) impeller threads.

3. Apply anti-seize compound to the shaft (122) impeller threads.
4. Lift the impeller (101) using a strap or a chain/sling threaded through a vane passage

attached to the hoist.

5. Guide the impeller (101) into position to engage with the shaft impeller threads.

«
...
126
127
128
129
130
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: Gardena Pages: 17

Brand: Gardena Pages: 12

Brand: A.O. Smith Pages: 4

Brand: Battery Watering Technologies Pages: 2

Brand: Pentair Pages: 16

Brand: DROPSA Pages: 9

Brand: Bard Pages: 27

Brand: STERWINS Pages: 232

S3C1-E6.2 230/3

Brand: GORMAN-RUPP PUMPS Pages: 51

3D TRASAR Series

Brand: Nalco Pages: 243

FLOJET R4320143A

Brand: Xylem Pages: 38

LX ACDC/M+K 100 A

Brand: Logitex Pages: 18

Brand: Little Giant Pages: 16

Brand: Homelite Pages: 36

Brand: FLYGT Pages: 172

Brand: Trane Pages: 44

Brand: DAB Pages: 37

Brand: C.P.A. Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands