ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 15

Page: 15 / 160

Transportation and Storage

XHD Installation, Operation, and Maintenance Manual

Table 1: Methods

Pump type

Lifting method

A bare pump without lifting
handles

Use a suitable sling attached properly to solid points like the casing, the
flanges, or the frames.

A bare pump with lifting lugs Use a suitable sling attached to the lifting lugs in the casing and bearing

cartridge.

A base-mounted pump

Use slings under the pump casing and the drive unit, under the base rails,
or through lifting lugs, when provided.

Examples

Figure 1: Example of a proper lifting method

Figure 2: Example of bare pump proper lifting method

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands