ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 86

Page: 86 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

3. Move the casing volute liner (561) out of and away from the gland half casing.

Figure 59: Removal of volute liner - metal lined

4. Remove the seal cover-to-volute liner gasket (351Q).
5. Remove the volute liner retention studs (356K) from the casing volute liner (561) using a

metric stud driver.

Figure 60: Removal of volute liner retention studs

Remove the expeller (optional feature)

1. Remove the impeller hub o-ring (412U).
2. Remove the expeller (263) from the shaft (122).

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands