ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 119

Page: 119 / 160

Maintenance

XHD Installation, Operation, and Maintenance Manual

117

Install the gland half casing and seal cover

1. Install the tapered alignment studs (375B) into the gland half casing (100D) using a metric

stud driver.

Figure 110: Gland half casing and seal cover installation

a) Install the seal cover into the casing.
b) With bolts and clipped washers (354A) (388A).

2. Attach the hoist hook to the gland half casing (100D) lifting lug, such that the casing

discharge will be oriented properly for the application.

3. Lift the gland half casing (100D) into position and move forward until it is flush with the

pedestal (131) by guiding the tapered alignment studs through the pedestal flanges.

4. Install the hex nuts (427D) onto the tapered alignment studs (375B).

Summary of Contents for Goulds Pumps XHD

































































































































































Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands

ITT Goulds Pumps XHD, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps XHD

Reviews:

Related manuals for Goulds Pumps XHD

Brands by name

Popular brands