ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 26 | Manualshive

Page: 26 / 160

background image

Installation

XHD Installation, Operation, and Maintenance Manual

24

NOTICE:
Remove all dirt from the mounting pads in order to ensure that the correct leveling is
achieved. Failure to do so can result in equipment damage or decreased performance.

a) Put one machinist's level lengthwise on one of the two pads.
b) Put the other level across the center of the two pads.
c) Level the pads by adjusting the four jackscrews in the corners.

Make sure that the machinist's level readings are as close to zero as possible, both
lengthwise and across.

Item Description

1.

Driver's mounting pads

2.

Machinist's levels

3.

Foundation bolts

4.

Jackscrews

5.

Grout hole

6.

Pump's mounting pads

Figure 15: Level pump mounting pads

6. Hand-tighten the nuts for the foundation bolts.
7. Check that the driver's mounting pads are level and adjust the jackscrews and the

foundation bolts if necessary.
The correct level measurement is a maximum of 0.167 mm/m | 0.002 in./ft .

«
...
24
25
26
27
28
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: Sanden Pages: 26

Brand: SAHP Pages: 41

Brand: Jandy Pages: 16

Brand: Davey Pages: 28

Brand: laguna Pages: 8

Brand: Flux Pages: 80

Altherma 3 H F+W EABH16DF9W

Brand: Daikin Pages: 60

Brand: SAMES KREMLIN Pages: 49

Brand: Panduit Pages: 7

Brand: Texas Equipment Pages: 11

F 550 GS Series

Brand: Flux Pages: 116

Brand: HERBORNER pumpentechnik Pages: 39

Brand: Santon Pages: 12

Brand: INOXPA Pages: 19

Poolex MEGALINE FI

Brand: poolstar Pages: 38

Ephoca HPAC 2.0

Brand: Innova Pages: 40

SUF-130- 300/400/500

Brand: State Water Heaters Pages: 76

ISMATEC REGLO-Z Digital

Brand: Idex Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands