ITT Goulds Pumps XHD Installation, Operation And Maintenance Manual Download Page 123 | Manualshive

Page: 123 / 160

background image

Maintenance

XHD Installation, Operation, and Maintenance Manual

121

2. Insert the casing volute liner retention studs into the casing volute liner (561) using a metric

stud driver.

Figure 116: Volute liner stud installation

3. Coat the seal cover-to-volute liner gasket (351Q) with lubricant and install into the casing

volute liner (561).

4. Support the casing volute liner (561) using the proper end of the Goulds-provided impeller/

casing volute hook tool.

5. Lift the liner into position and insert into the gland half casing (100D) using the installed

retention studs (353K) as a guide.

Figure 117: Volute liner installation

6. Secure the casing volute liner (561) to the gland half casing (100D) by installing and fully

tightening the volute liner retention hex nuts (355C).

Install the impeller - Metal-Lined

Two (2) people should work together to install the impeller for safety purposes.
1. Loosen the adjustment plate bolts (352G) and nuts (427D) but DO NOT remove bolts or

adjustment plates (234F). Bolts should remain finger-tightened to keep rotating assembly
constrained to the pedestal.

2. Slide the power end forward towards the suction side of the pump to allow better access to

the shaft (122) impeller threads.

3. Apply anti-seize compound to the shaft (122) impeller threads.
4. Lift the impeller (101) using a Goulds-provided impeller hook or a chain/sling threaded

through a vane passage attached to the hoist.

«
...
121
122
123
124
125
...
»

Summary of Contents for Goulds Pumps XHD

































































































































































Reviews:

No comments

Related manuals for Goulds Pumps XHD

Brand: Zoeller Pages: 4

Brand: Mallory Pages: 7

Brand: Panasonic Pages: 100

Aquarea WH-MDF09C3E5

Brand: Panasonic Pages: 90

Brand: Panasonic Pages: 80

Brand: Mueller Pages: 46

Brand: OSO Pages: 44

Brand: Remco Pages: 5

Milton Roy Milroyal Series

Brand: Accudyne Industries Pages: 68

Brand: Fluke Pages: 2

Brand: Landustrie Pages: 16

Brand: Stuart Turner Pages: 16

FLOW-PRO 350MOP

Brand: EUROM Pages: 32

Brand: Austria Email Pages: 40

AQUA OCEAN AQ4000

Brand: ICA Pages: 16

Brand: Daikin Pages: 16

Dura-Power DRE - 120

Brand: A.O. Smith Pages: 2

Brand: A.O. Smith Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands