IBM 60 User Manual Download Page 140

Page: 140 / 166

Table

7-1 (Page 4 of 10). Messages and Recovery Actions

Display Message

SRC

Description

Recovery Action

ETHERNET ERROR

A452

Ethernet TCP/IP network
error.

1. Report network problems to site

system network administrator.

2. Call for service if the problem

continues.

ETHERNET ERROR

A453
A454

Ethernet TCP/IP
communications error.

1. Restart the printer, and retry.
2. Call for service if the problem

continues.

ETHERNET ERROR

A455

Ethernet TCP/IP host error.

1. Restart the printer and retry.
2. Call for service if the problem

continues.

ETHERNET ERROR

A456

Ethernet TCP/IP network
error.

1. Report network problems to site

system network administrator.

2. Restart the printer, and retry.
3. Call for service if the problem

continues.

ETHERNET ERROR

A457
through
A45B

Ethernet TCP/IP
communications error.

1. Report network problems to site

system network administrator.

2. Restart the printer, and retry.
3. Call for service if the problem

continues.

ETHERNET ERROR

A45C

Ethernet TCP/IP Invalid
start up.

1. Report network problems to site

system network administrator.

2. Restart the printer, and retry.
3. Call for service if the problem

continues.

ETHERNET ERROR

A45D

Ethernet TCP/IP Invalid
run-time.

1. Report network problems to site

system network administrator.

2. Restart the printer, and retry.
3. Call for service if the problem

continues.

FORM MISMATCH FOR
AUTOSWITCH

A different form name was
loaded in a tray previously
designated as an
autoswitch tray. While this
different form name remains
loaded in this tray, the
previously designated
autoswitching will not occur.

Not an error; informational only.

FRONT COVER OPEN

0103

The front cover is open.

Close the front cover (if you have
finished procedures requiring the door
to be open).

FUNCTION UNAVAILABLE
MUST BE OFFLINE

You cannot perform this
function when the
attachment is enabled.

Have the key operator disable the
attachment and retry.

FUNCTION UNAVAILABLE
STOP PRINTER

You selected a menu item
that is not valid when the
printer is printing.

1. Press Enter to clear the message.
2. Press Stop to make the printer

NOT READY.

3. Re-select the menu item.

FUSER UNIT: REPLACE
NOW

1005

The fuser needs to be
replaced.

Replace the fuser unit.

7-22

InfoPrint 60 User's Guide

Summary of Contents for 60







































































































































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

IBM 60, User Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands