IBM 60 User Manual Download Page 143

Page: 143 / 166

Table

7-1 (Page 7 of 10). Messages and Recovery Actions

Display Message

SRC

Description

Recovery Action

PAPER JAM

4032
4033

A paper jam at input station
(IS top sensor)

Follow directions for clearing paper
jams.

PAPER JAM

4034

A paper jam at input station
(double feed detector).

Follow directions for clearing paper
jams.

PAPER JAM

4037
4038

A paper jam at registration
station (IS timing sensor)

Follow directions for clearing paper
jams.

PAPER JAM

403E
403F

A paper jam at the
registration station (paper
top return sensor).

Follow directions for clearing paper
jams.

PAPER JAM

600A

Paper jam on paper path B
(drum wrap sensor).

Follow directions for clearing paper
jams.

PAPER JAM

600B

Paper jam on paper path C
(switchback path sensor).

Follow directions for clearing paper
jams.

PAPER JAM

600C

Paper jam on paper path D
(return path 1 sensor).

Follow directions for clearing paper
jams.

PAPER JAM

600D

Paper jam on paper path E
(return path 2 sensor).

Follow directions for clearing paper
jams.

PAPER JAM

600E

Paper jam on paper path F
(PF out sensor).

Follow directions for clearing paper
jams.

PAPER JAM

6010

Paper jam on paper path 20
(HR out sensor).

Follow directions for clearing paper
jams.

PAPER JAM

6028

The simplex sheet is
wrapped around the
photoconductor.

Follow directions for clearing paper
jams.

PAPER JAM

6029

The duplex sheet is
wrapped around the
photoconductor.

Follow directions for clearing paper
jams.

PAPER JAM

6038
6039

A paper jam at fusing
station.

Follow directions for clearing paper
jams.

PAPER JAM

6040

A paper jam at switchback.

Follow directions for clearing paper
jams.

PAPER JAM

6044
6045

A paper jam at paper feed
exit.

Follow directions for clearing paper
jams.

PAPER JAM

6048
through
604B

A paper jam at return feed
path.

Follow directions for clearing paper
jams.

PAPER JAM

7041

Paper jam on paper path 21
(side stacker path sensor).

Follow directions for clearing paper
jams.

PAPER JAM

7078

Paper jam at base stacker
(before the base stacker out
sensor).

Follow directions for clearing paper
jams.

PAPER JAM

707A

Paper jam at upper stacker
(before the upper stacker
out sensor).

Follow directions for clearing paper
jams.

PAPER JAM

7080
7081

Paper jam at side stacker
(side stacker jam sensor).

Follow directions for clearing paper
jams.

Chapter 7. Handling Operation Problems

7-25

Summary of Contents for 60







































































































































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

IBM 60, User Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands