IBM 60 User Manual Download Page 120 | Manualshive

Page: 120 / 166

background image

The following table shows the area of the machine that corresponds to the indicator
lights.

Indicator Light

Area of Paper Jam

A

Top auto-eject door

B, 6

Bottom door

C, 10

Base stacker

14

Side stacker

13

EP module area

7, 8, 9, 11, 12

Paper feed module area

1, 2, 3

Tray area

Clearing a Paper Jam

The printer stops printing when a misfeed occurs, and the PAPER JAM message
appears. Paper jams may occur in several areas of the printer. Check the paper
path thoroughly. Remove all paper along the paper path in the order described in
the following procedure.

To clear the paper jam and operator panel message, do the following:

1. Check the indicator light on the operator panel.

2. If an arrow is lighted, open the corresponding door or tray and remove the

paper, starting with the top door. Paper is auto-ejected from this door.

3. Check the paper jam indicator lights again. If any lights remain lit, clear the

paper from the corresponding area.

4. Some indicator lights go off immediately when the paper is removed. The

indicator lights for the EP and the paper feed modules temporarily remain on.
Press the Start key to verify that all jams are cleared, to clear the Operator
panel message, and to continue printing.

Note: Pages removed from the paper path reprint automatically when the printer
starts printing again. If the printer is warming up, it may take a few minutes to start
printing.

7-2

InfoPrint 60 User's Guide

«
...
118
119
120
121
122
...
»

Summary of Contents for 60







































































































































































Reviews:

No comments

Related manuals for 60

Brand: Gateway Pages: 42

Brand: Radio Shack Pages: 30

Brand: Radio Shack Pages: 42

Brand: Radio Shack Pages: 192

Brand: Radio Shack Pages: 274

Brand: Radio Shack Pages: 44

Brand: Radio Shack Pages: 30

Brand: Acer Pages: 102

DEC 3000 Model 400S AXP

Brand: Digital Equipment Pages: 13

Brand: Morrow Pages: 162

Brand: NRG Systems Pages: 65

Brand: Asus Pages: 2

Brand: Asus Pages: 8

Brand: Asus Pages: 2

ASUSTEK ROG Strix G15DK

Brand: Asus Pages: 41

Brand: Asus Pages: 16

Brand: Asus Pages: 44

Brand: Asus Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands