IBM 60 User Manual Download Page 22

Page: 22 / 166

Functions-Internal View

The following information lists each part and function labeled on the previous figure:

Item

Function

Electrophotographic (EP)
module handle

Release the paper feed module lever and two lock
levers, then pull the EP module handle forward to
access the EP module components.

Electrophotographic (EP)
module

Consists of the drum, cleaner unit, developer unit,
and the toner cartridge.

Toner cartridge

Insert the toner cartridge into the slot to replace toner.

Developer mix duct

Mount the developer mix bottle onto the developer
mix duct to replace the developer mix.

Drum

Part of the EP module. Consists of the drum and a
photoconductor installed on the drum.

Paper feed module lever

Turn to the RELEASE position, then pull forward to
access the paper feed module components.

Paper feed module

Consists of the transfer belt unit and fuser assembly.

Relocation

Whenever the printer is to be moved to another location, order a relocation kit. The
customer engineer disconnects and reconnects the printer. The customer is
responsible for ordering the relocation kit from an IBM Marketing representative.

1-4

InfoPrint 60 User's Guide

Summary of Contents for 60







































































































































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

IBM 60, User Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands