IBM 60 User Manual Download Page 147 | Manualshive

Page: 147 / 166

background image

Abbreviations

This list describes the acronyms and abbreviations used
in this manual and in the other manuals that are part of
the InfoPrint 60 documentation library.

ABIC

Adoptive Bi-Level Image Compression.

AEA

Alternate Exception Action.

AFCCU

Advanced Function Common Control Unit.

AFIG

Advanced Function Image and Graphics.

AFP

Advanced Function Presentation.

Advanced Function Printing.

AFPDS

Advanced Function Printing Data Stream.

AFPF

Advanced Function Print Finishing.

AIX

Advanced Interactive Executive.

APA

All-Points Addressable.

ARQ

Active Record Queue.

ASHRAE American Society of Heating, Refrigeration,

and Air Conditioning Engineers.

CCITT

Comite Consultatif International
Telegraphique et Telephonique.

CCW

Channel Command Word.

CE

Customer Engineer (IBM).

CPI

Characters per Inch.

CSW

Channel Status Word.

CU

Control Unit.

DASD

Direct Access Storage Device.

DPE

Decompression Performance Enhancement.

DPI

Dots per Inch.

EBCDIC

Extended Binary-Coded Decimal Interchange
Code.

EC

Engineering Change.

EHC

Exception Handling Control command.

EMTF

European Money Transfer Form.

EP

Electrophotographic.

ESCON

Enterprise Systems Connection.

ESMM

End Select Medium Modification.

FORMDEF Form Definition.

HAID

Host-Assigned ID.

HFSI

High Frequency Service Items.

IHF

Image Handling Facility.

IML

Initial Microcode Load.

IP

Internet Protocol.

IPDS

Intelligent Printer Data Stream.

ISO

International Organization for
Standardization.

JES2

Job Entry System 2.

JES3

Job Entry System 3.

LCD

Liquid Crystal Display.

LED

Light-Emitting Diode.

LF

Load Font command.

LU

Logical Unit.

MB

Megabyte (1MB=1 048 576 bytes).

MICR

Magnetic Ink Character Recognition.

MIH

Missing-Interrupt Handler.

MMR

Modified-Modified READ 2 dimensional
image.

MR

Modified READ; (READ=Relative Element
Address Designate) 2-dimensional image
compression algorithm. Also referred to as
CCITT Group 3.

MTU

Maximum Transmission Unit.

MVS

Multiple Virtual Storage.

NACK

Negative Acknowledge reply.

NOP

No Operation instruction.

OBR

Outboard Recorder.

OCR

Optical Character Recognition.

OPC

Organic Photoconductor.

OS/VS

Operating System/Virtual Storage.

PAGEDEF Page Definition.

PC

Photoconductor.

PEL

Picture Element.

PEM

Print-Error Marker.

PSF

Print Services Facility.

RAM

Random Access Memory.

RPQ

Request for Price Quotation.

RRL

Request Resource List.

SCSW

Subchannel Status Word.

SDLC

Synchronous Data Link Control.

SMM

Select Medium Modification.

SNA

System Network Architecture.

SRC

System Reference Code.



Copyright IBM Corp. 1996

A-1

«
...
145
146
147
148
149
...
»

Summary of Contents for 60







































































































































































Reviews:

No comments

Related manuals for 60

Brand: Gateway Pages: 126

Brand: IBM Pages: 68

Brand: IBM Pages: 54

Brand: Medion Pages: 2

Brand: Sysgration Pages: 27

Brand: Aaeon Pages: 117

DECstaion 5000 240

Brand: Digital Equipment Pages: 62

Brand: Vecow Pages: 160

Brand: Apricot Pages: 139

Brand: Contec Pages: 116

Brand: Amiga Pages: 113

Brand: Uplift Desk Pages: 2

Brand: Epson Pages: 117

Brand: Epson Pages: 184

CW3S16 Canadian Product

Brand: Epson Pages: 218

Brand: Epson Pages: 115

Brand: Epson Pages: 180

Brand: MSI Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands